Saab 93 Key Fob Replacement
Saab 93 key fobs can be costly to replace. However the process is simple.
All you require is a flathead screwdriver as well as some patience. Put the screwdriver in the middle of the case and slowly open it.
It is recommended to keep spare keys and fobs. You can avoid being stranded and having to pay towing fees.
How do you replace a battery
All car key fobs that enable and lock your vehicle remotely have a battery that will eventually fail. If that happens, owners can replace the battery of their key fob themselves in just a few steps. The key fob has two plastic flaps on one side that you have to open in order to take out the old battery and then install an alternative one. The replacement battery is an ordinary CR1632 coin cell, and the process for installing it is relatively straightforward.
After you have removed the emergency key, you can use the flathead screwdriver on small pieces of wood to break the case. Don't force the case too hard because the electronics are fragile and may be damaged by excessive pressure.
Saab produced some amazing cars. Many of them remain in existence today. One of the big problems with these cars, however, is their ignition keys. They're not durable, and the keys may become spongy or loosen with time. If you are a Saab owner loses only one functioning key, it could be expensive to purchase an additional key at the dealership, since they will need to replace the entire computer module and then program it to the new key to convince the car that you're not trying to take it. You can save money by replacing the case.
How do I remove the manual key
Batteries are present in all key fobs used to lock and unlock vehicles. They are of a limited duration. If you're like many people, they will eventually go out. Fortunately it's possible to replace the battery that controls your key fob is very easy. The only challenging part of the process is removing the old battery from the case. However, with a little patience and a flathead screwscrewdriver, you can complete the task.
After you've installed the battery, it's time to put everything back together. You'll need a flathead screwdriver to open the replacement case of the key fob. Insert the screwdriver into the slot in the middle. Gently move the case until you're able to take it off.
You may have to re-program the new key fob in case the previous key fob has lost its connection to the security system of your car. This can be accomplished by following the manual learn procedure for adding a brand new FOB to your Saab 9-5. This method is not a way to erase previous keys that you have learned. You can still utilize existing FOBs, in case you have to re-program them. To begin this process the FOB to be programmed must have a mechanical key cut matching that of the vehicle.
How to Change the Case
Whether you're replacing the battery or manual key, it's recommended to replace the case as well. The cases can wear out quickly, especially after prolonged use. It's easy to change the case of your SAAB 9-3 and you won't require any special tools.
The first step in changing the case is to remove the manual key from the fob. This can be done by pressing the SAAB logo and then pulling out the manual key. It may be necessary to use a bit of force to remove the manual key from the fob.
After you have removed the manual key from the case, you can begin to remove the electronic components. You'll need a flathead screwdriver in order to do this. Be careful not to harm the electronics inside, so use care when using your screwdriver. After you've removed the electronics, you'll need to remove the battery. After you've replaced the battery, you can put everything back in a new case. You can purchase replacement cases on the internet for a very low cost.
How do I program the new key
All key fobs, which allow you to lock and unlock your vehicle remotely, contain batteries. However they have a short lifespan. It is vital to change the battery in your key fob at least every three to four years. Fortunately, this is an easy procedure that can be completed at home. All you need is patience and a small flathead phillips screwdriver.
The first step is to remove the manual key. This can be done by pressing the blue SAAB logo on the fob of your key and pulling the emergency key out. It may take some force however, the key should come out easily. After saab ignition key opened the key fob, you can remove the battery by gentle pressing the screwdriver inside the slot that is in the middle. This will split the case, making it easier to access the electronic components.
It is now time to program the key. This can be done by following the instructions in this video posted by YouTube user Cyclone Cyd. This is an excellent video channel that provides instructions on how to carry out simple repairs and maintenance on vehicles.
A key fob could be an ideal place to store an additional car key in the event that you break or lose your original. You can purchase a replacement keyfob on the internet or from local locksmiths like United Locksmith. The cost is significantly less than buying the key at a dealership. They will charge for the key and then program it into your car.